Local Making Community

Papier-mâché Lampshade

01- Intro

This assignment revolves around using locally sourced fibres or those intercepted from a waste stream to develop and create a physical product.

From the start I considered my lack of experience with traditional fibre techniques like sewing, weaving, crocheting, etc to be insufficient for a satisfactory product outcome, therefore I explored alternate techniques. Along with that, assignment 1 delved into the cultural aspects of fibre techniques, as such I wanted to create something inspired by my culture.

02.1- Development

At the start I only had a very vague idea of what I wanted to do and was kind of aimless and directionless. I began experimenting to try and lead into some sort of idea of a final product.

At first I was inspired automotive and cycling parts made with fibreglass and more specifically carbon fibre as I cycle myself. A flexible woven fibre(the carbon fibre itself) is formed around a mold, then resin is lathered on to bind everything together.

So I tested layering two piece of scrap fabric, then saturating it with generic craft glue. The outcome was a tough, plastic-like sheet that remained somewhat flexible.

Next, I attempted to use corn starch gloop as a biodegradable alternative to the generic PVC craft glue I had first used.

After drying, the PVC glue tiles remained discoloured as if it was still wet, the starch tile returned to its original colour and retains far more flexibility.

I laid two layers of scrap fabric together, then applied a liberal amount of the corn starch solution, making sure to completely saturate the fabric. The soaked fabric took absolutely forever to dry, up to 2 days even with the help of a heater fan.

At this point, I had decided to go for the simple end product of a lamp/ lampshade because of how the glued fabric’s properties could be helpful in creating certain forms and shapes.

I created two shapes, a hexagonal lantern inspired lamp and a more traditional circular lampshade. I first modelled them on Rhino, then printed them out to use as stencils. The hexagonal lamp’s form was loosely inspired by Chinese lanterns, while the cone is just a regular lampshade.

The treated fabric was too weak to support the structure and this attempt was a failure. But at least a rough form was able to be created despite not working out.

02.2- Development cont

Following the failure of the fabric tests, I deviated to the idea of using paper(which counts as a fiber) to continue with a lamp/ lampshade as a final product.

As I was going along with a slight cultural influence, I figured trying paper could be a cool idea. China was one of the first civilisations to invent modern paper made using pulp instead of something like the woven flax leaves other older civilisations used. The idea was to recycle paper scraps to make pulp, then turning that into usable paper for the lampshade.

I had a vague idea of what to do since I remember an activity from kindergarten where we used newspaper to make our own recycled paper.

The art supply store had screen printing frames but they were made of metal thus very expensive. Instead I bought some laundry mesh stuff at the dollar store and use an old canvas’ frame, then nailed everything down using the heavy duty stapler at the Design Lab.

For the paper pulp, I decided to put some of my old worksheets to use along with some extra paper scraps I salvaged from the design space shelves.

To make the pulp, I cut down and torn up the scrap paper then let it soak in a container for at least an hour to soften the paper. After that I threw the paper mulch into a hand cranked food processor that I also got at the dollar store because a proper blender was too expensive. I ground the mulch down till it was a consistent slop.

Initially I had used my shower as my workshop because I didn’t have much else. I plugged the drain to let the basin fill with water show that the water could suspend the material for handling.

But in the end the resulting paper was rough due to the clumsy handling as well as using already once recycled paper materials. For the following attempt I switched to mostly virgin pulp print A4 paper sheets as it should result in a smoother texture and I had an abundance of because I was handed a bunch of worksheets and fliers I never bothered to read.

I had also gotten a large container as I figured out that suspending the pulpy particles in water, letting them float around, then pulling the mesh frame through and out the water was a better method that resulted in a cleaner piece of paper. Eventually I phased out the pre-recycled brown paper as they wouldn’t shred properly and stayed relatively intact.

Eventually I figured out the process to the point where I could churn out a piece every few hours even with one small frame. I sieve the paper, let it rest for a while, prop it up against something while a heater works overtime to dry it, when its dry enough I tear the sheet out, then hang it up to fully dry, then the cycle repeats.

Using the paper I had made, I traced the shape from the stencil, cut, and then glued the pieces together.

For the lighting itself, I tore down an old desk lamp I no longer had any use for, beats taking LED’s from the design lab.

I soldered the wires to fit the height of the display setup, making sure the connections and subsequent wrapping over were strong enough. The lamp itself is rather light so it is suspended by the plug only.

Using some MDF boards from the Design Lab scrap bin, I made these disks that everything attaches onto.

Then, in the end these parts come together.

03- Final Product

03- Conclusion

The lamp itself functions, as in the solders did not fail thankfully.

Huge issue I realised at the end was that I was terrible at math, so I calculated the cone wrong, and it ended up being smaller than the laser cut MDF disks and didn’t fit properly and I had to fill in the gap with scraps. Alongside that, because of the misalignment, the bottom rim wasn’t straight, I could have used a simpler shape like a trapezoid instead of a cone so that I could have 4 straight easy to measure edges.

Another issue is that the glue I used to put everything together severely weakened the bond of the paper to itself, any moisture breaks down the bond and I had to compensate with a ton of masking tape in the interior face to strengthen the joins and prevent the whole lamp from exploding in on itself.

If I had decided on a direction earlier on, I could have ended up with a better final product and a less rushed process.

Then, if I had known a mortar was relatively affordable, I would’ve gotten one to further grind down the pulp for a better finer finish, additionally the water I used during the process should’ve had 10-20% of its volume as some sort of glue to improve the strength of the paper, but that amount of glue is unfeasible.

At least I got a somewhat acceptable product in the end, the final product was rushed and assembled an hour before the submission deadline.


Comments

Leave a Reply

Your email address will not be published. Required fields are marked *